How to fix the yellow light on the ps3

how to fix the yellow light on the ps3

How to fix Yellow Light of Death (YLOD) PS3. FULL GUIDE

May 09, In this video iFixit's MJ demonstrates how to use their PlayStation 3 Yellow Light of Death repair kit. This kit will repair the Yellow Light of Death when c. Jun 26, This video shows how to repair your ps3 if it has the dreaded yellow light of death, without opening it up!Please let me know if this video helped and if it Author: si leeds.

There is an extremely high chance the only reason you are reading this guide is because your PS3 has died and you are looking for any way possible to fix it. You will know you have a major problem when you press the ON button, but all that happens is the red light flashes and nothing else. This is called yellow light of death or YLOD because the red light actually flashes yellow quickly before it starts flashing red. Just to save you some time instead of reading all this leave it unplugged for at least two hours then come back and see if it turns on.

If it did, sweet! Hardest way is only if you absolutely have to, meaning opening it. Not only that, but the game that was stuck was Gran Turismo 6 which is by far the most important game I own since I use it to make this site. I tried everything, but it was stuck so bad I was forced to open it myself to get it out. I also made some critical mistakes and broke some pieces which I will be giving tips on how to fix if that happens to you.

It was basically a worst case scenario, but I was determined to fix it. Ideally in the cheapest way possible of course. This guide is for the old school fat PS3 mine was 80GBbut some techniques can be applied to later versions such as backups, fan test etc. I strongly suggest you bookmark, save, share with othersand whatever other ways you can think of to get this guide out to everyone.

Trust me the last thing you want to be doing is searching all over the internet on what to do when it happens. I decided to make this guide as a lot of the problems I had were all over the internet and not easily found in one place.

I had to read multiple guides and watch many videos before I understood exactly what to do. This guide is going to be a one stop shop. For legal reasons if you follow any part in this guide and break something or hurt yourself etc that is your own fault and I take no responsibility for it. Before I list the tools you will need you need to ask yourself a few simple questions. Have you ever taken apart an electrical device? Do you have any experience with repairs on small electronics?

Do you have any idea what you are doing at all? If you answered no to one or all of those questions you are qualified! Hard to say exactly the reason why your system has decided to die. Usually it is because the system is very old or you play a lot which equals years of abuse. The cleaner the environment the PS3 is in the longer it should last since there will be less dust getting sucked inside, but eventually it can still die.

The most common reason for YLOD is because it has overheated. The parts inside only last so long and years of heavy game playing puts a lot of stress on them. What I find very ironic is the reason the PS3 has died is because it overheated and the way to fix it is with extreme heat. You would think that would be the worst thing for it, but you would be wrong.

Browse the categories below quickly before you buy anything. No matter what choice you made everyone needs a blow dryer to bring it back to life. Even if you plan on doing a full repair of the system the heat trick step 10 with the blow dryer should be done first to get your saves off. Number 1 is, is your PS3 still under warranty? If it is I highly suggest you contact Sony for repairs and let them do it. No point in risking possibly ruining your system forever when they how much did oprah donate to obama campaign repair it for free.

Since you are probably out of warranty continue to read on. Do realize what does low down mean if you have a disk stuck inside or important game saves there is an extremely high chance Sony will NOT return them. Before you do anything ideally getting the disk out first is best. Even if you are under warranty getting the game out allows you to keep the how to sharpen a wood auger bit. No point in buying a game you already own again when its just sitting right in front of you.

The first how to get abs in 10 days at home to try is called the fan test.

Turn the system off from the back switch, hold the eject button, then keep holding while you turn the system on from the back. This should set the fans into max speed and also eject your disk. If this works, awesome! As far as I understand only newer fat PS3 systems this is built into. Video shows a PS3 Slim which has no back button. For Fat versions use the back button instead of how to get dvd movies on your ipod like I said above.

I had old saves backed up, but they were days old. Meaning pretty much the past year of saves would be gone. This is really important question to ask because even if you buy a brand new PS3 you can NOT simply put the old hard drive into the new system and still have everything the way it was.

The new system will tell you to format the hard drive losing ALL your data. Years of work playing these games and now it will all be gone. If you picked the second option please note we will be using extreme heat which may or may not melt your stuck disk and ruin your hard drive.

The next few steps will explain how to take everything apart which is the least risk to game and hard drive. I suggest everyone take out the hard drive first. Why risk the possibility of heat destroying it when taking out just one screw can save it? To take the hard drive out look on the side opposite what are some angel names the vents for the little piece of plastic and pop it off.

You can use your nail to pop it or a knife, screwdriver etc. Just unscrew it with the Philips 1 Screwdriverthen slide the hard drive over in order to use the tab to pull it out. Just set it aside for now and obviously make sure not to drop it or destroy it. You do not need to take the hard drive out of the hard drive case just yet like their guide shows.

Video shows how to replace the hard drive with a new drive, but stop at for just taking it out. On one hand you can move on to the heat step step 10 which will bring your PS3 back to life and just press eject button to get the game out.

However the risk is melting the game inside the system ruining the system forever. If the game is super important like GT6 was to me risking melting it in the system was not worth it. Blu ray disk are supposed to be super strong and not melt very easily plus the game is inside the Blu ray drive which acts as a metal enclosure so the chance of it melting should be extremely low.

However there is still a small chance something goes wrong. I had many problems when I did it, but I have listed all the tips to avoid any problems you may run into in the rest of this article. I recommend trying the heat test step 10 with hard drive removed first. If the game is super important opening it is your only option. There are only two wires you need to unplug, but one is much easier to destroy, ruining the system forever.

I found out the hard way by breaking this wire connection like an idiot, BUT found a way to repair it and still have everything work perfectly fine.

Before I get into opening it up and all the hard stuff I have been getting comments asking what is the point since PS4 and newer systems are out? Other than of course getting the saves off and fixing your system the whole point is the PS3 is an excellent media player. It is by far the best media player you can buy for the price that makes any home theater setup much better.

As you will read later in this guide I bought a new PS3 and use that as my main one now, but my old PS3 that broke is how to make a subbuteo table moved to a different TV to give it all the benefits the PS3 provides. First step to this is realize this has to be done.

No need to cry and complain about it anymore. This system is meant to be built and repaired and everything should come apart fairly easily. Some sections may need a little more effort, but before you do this always double how to win an election a panorama guide you got all the screws out. Behind it is a piece of rubber that you remove then the first screw which unlocks everything.

The first screw you use the T10 Torx Screwdriver while all the others inside you use the Philips 1 Screwdriver. I also have a easy to follow video below showing you exactly what to do.

They know exactly what they are doing and make it easy to make sure you get how to check if you have student loans correct screws.

I suggest reading the tips below first just to give you an idea of what you may run into while reading their guide. Do this for all screws in this guide. Not all screws are the same and need to be placed back exactly where they came from. The easiest way is unscrew one and place it right beside the hole it came from like shown in the picture. Be extremely careful undoing and putting back the ribbon cable.

Watch this video for a view of how it works. Follow along ONLY until If you have the repair kit for full repair watch it all. I talk about that in step how to do colored acrylic nails The good news is you are so close to getting the game out!

You will notice there is lots of computer chips and wires hanging off the drive which I just left on mine. Just follow the video below as he makes it simple, but the next two paragraphs are important. You do not want to screw this up and have to take everything apart again to fix your mistakes like what happened to me. The screws are different lengths and colors and must be put back the same way.

Playstation 3 Yellow Light of Death (PS3 YLOD)

Nov 09, Fix Blinking Yellow Light of Death (YLOD) Fix the Solid/flashing Red Light. Fix the Flashing Green Light issue. Fix the 3 beeps issue. Fix the Red Screen. Fix the Black Screen of Death. Fix a Freezing Screen (during game-play or during the menu) Fix the HDMI issue on your PS3. Fix the DNS error issue on your PS3. Peel Off Thermal Pad Covers. Apply Fresh Thermal Pads. Peel the plastic covers off one side of the new thermal pads and apply the fresh thermal pads to the motherboard in the locations indicated: large square pads (pictured red), small square pads (pictured . You can buy a new PS3 which is costly, but if your existing PS3 is getting old, it might be on the downhill slope and pick up more errors even if you get the yellow light of death fixed. 2. You can send it away to Sony for repair, but the figures I have seen banded about online start from ?, so not a cheap solution.

Don't try to fully remove the cover for now. It's still connected by the memory card reader cable. Using a nylon spudger, delicately lever up the latch that secures the cable for the memory card reader in its connector. Now remove the cable from its connector. To do this, delicately pull the cable. No resistance should be felt. Don't try to completely remove the Blu-Ray reader from your PS3 as it's still connected to the PlayStation 3 by a cable.

As indicated in the photos, use the nylon spudger to unclip the two plastic brackets. These brackets secure the front panel to the internal frame of your PS3.

Like in the photos, unclip the 3 brackets holding the rear panel to the internal frame of your PS3. Do not hesitate to lever it up with a spudger to remove it. Do step 46 again, applying a few drops of ArctiClean 1 solution on the second processor graphics.

Heat the chips for seconds each with a heat gun on low power, or a hair dryer for around 1 minute. Using the plastic card provided in our YLOD kit , delicately spread the thermal paste across the processor. Using the nylon spudger carefully peel the protective films off the thermal pads blue in colour. Our goal is to make repairing accessible to all. Our team introduces you Captain Repair, an on-site repair service.

The good point about it is that you can have the repair done at home, at work or at a coffee shop! All rights reserved to SOSav. Why not you?

Any issues with the PS3 are shown with this yellow light being lit when turning on the console, followed by a flashing red light that shows the PS3 won't restart. This problem is generally caused by the PS3 overheating internally and melting the solder. This guide provides the solution to the YLOD. This solution is nowhere near perfect, but is one of the best repairs available!

Do you have the spare parts to do the repair? Some parts are missing! Recommended repair kit. See product Add to cart. Required spare parts. Required tools. Nylon Spudger. Guide format : Pdf Integrate. See in HD. Lift off the small silicone cover to release the screw that's holding the smart plate in place. Step 2 Use a torx screwdriver to unscrew the screw that was underneath the silicone cover just removed.

This screw, circled in red in the photo, secures the smart plate on your PS3. Step 3 Delicately push the smart plate cover down towards the bottom of the console. Step 4 Now lift the smart plate and remove it completely. Step 5 Using a cross headed screwdriver, now unscrew the 8 screws circled in red in the photo. Step 6 Now lift the top cover in order to remove it from the PlayStation 3. Step 7 Using a nylon spudger, delicately lever up the latch that secures the cable for the memory card reader in its connector.

Step 8 Now remove the cable from its connector. Step 9 Disconnect the power supply cable for the Blu-Ray reader. To do this, delicately pull the cable up to remove it from its connector. Step 10 Now delicately lift the Blu-Ray reader.

Step 11 As indicated in the photos, use the nylon spudger to delicately lift the latch. Step 12 Now delicately pull on the cable in order to remove it from its connector. Step 13 As indicated in the photos, use the nylon spudger to delicately lift the latch. Step 14 Now gently grasp the power board cable and remove it from its connector. Step 15 Unscrew the 2 cross headed screws circled in red in the photo. These secure the power board to the internal frame of your PlayStation 3 Fat.

Step 16 Now grasp the power board and remove it from its placement. Step 17 Unscrew the 2 screws circled in red in the photo. Step 18 You can now grasp and remove the bracket for the power supply board from its placement.

Step 19 Now unscrew the 6 cross headed screws circled in red in the photo. Step 20 Now remove the hard drive access door using the nylon spudger. Step 21 Lift the internal frame metal structure in order to remove it entirely. Step 22 Delicately unplug the power supply cable AC-In on the back of the power supply block. Step 23 Unscrew the cross headed screw circled in red in the photo. Step 25 Delicately unplug the power supply cable DC-In on the front of the power supply block. Step 26 Unscrew the 5 cross headed screws circled in red in the photo.

These secure the metal power supply block to the internal frame of your console. Step 27 Delicately lift the power supply block to remove it from its place. Step 28 As indicated in the photos, use the nylon spudger to unclip the two plastic brackets. Don't try to remove the front panel of your PS3 now, it's still attached by other brackets. Step 29 Turn over your PlayStation 3.

Step 30 Unclip the final bracket on the left holding the rear panel to your PS3. Step 31 Now, very delicately, lift off the rear panel. You shouldn't feel any resistance. Step 32 With the nylon spudger move the fan cable delicately out from under the black plastic clip. Step 33 Unplug the fan from the power supply. Step 34 Unscrew the 4 cross headed screws circled in red in the photo. Step 35 Remove the first support bracket using the nylon spudger.

Step 36 Do the same for the second bracket. Step 37 Now lift the radiator heat sink up to delicately remove it from its placement. Step 38 Using a nylon spudger, delicately lever up the antenna connector in order to disconnect it.

Step 39 Move the antenna cable aside to prevent it interfering with future steps. Step 40 Now use the cross headed screwdriver to unscrew the 4 screws circled in red in the photo. Step 42 Using the nylon spudger, lift the latch for the connector carefully, releasing the cable. Step 43 Then disconnect the cable carefully, no resistance should be felt during this step. Step 45 Now lift the mother board in order to remove it completely.

Step 47 With a clean cloth, now clean off the thermal paste residue. Step 48 Do step 46 again, applying a few drops of ArctiClean 1 solution on the second processor graphics. Step 49 Still using the cloth, clean the residue dissolved by the ArctiClean 1 solution. Step 50 Now, using a nylon spudger, unfix the first thermal pad.

Step 51 Repeat the previous step, unfixing the second thermal pad from the other chip. Then, again with a clean cloth, clean the dirty areas until all thermal paste has been removed. Step 53 Now restart this operation on the other processor. Step 54 Heat the chips for seconds each with a heat gun on low power, or a hair dryer for around 1 minute. Step 56 Do the same thing again with the second chip. Step 58 Do the same thing again but on the graphics processor.

Step 59 Using a clean cloth, spread the ArctiClean 2 across the entire surface of both processors. Step 60 Now put a thin layer of thermal paste along the right side of the processor of your PS3 Fat. Step 61 Using the plastic card provided in our YLOD kit , delicately spread the thermal paste across the processor.

Step 62 Now put the thermal paste on the other processor, as indicated in the images. Now, again using the plastic card, spread it across the surface of the processor. Now, as indicated in the photos of this step, stick them onto the chips on the board. Step 64 Now do the same thing as the previous step, but on the grey chips. Step 65 Using the nylon spudger carefully peel the protective films off the thermal pads blue in colour.

Comments:

04.02.2021 03:33 Brasida:
Bro please Follow all steps in the video especially after completing installation

07.02.2021 12:58 Nashura:
Bang kalau naroto boleh gak